The Best RV Leveling Blocks in 2023

Comparisons, Guide, and Reviews

RV leveling blocks are critical items that many new owners tend to forget the importance of. When they set up camp and try to sleep in an angled RV, then they recognize the value of leveling blocks. An RV that shifts a little can cause items to fall off shelves, doors to swing open or close and even a fridge to crack and let precious cold air out.

Some people try to solve this problem by relying on jacks, but small and mid-sized SUVs don’t come with these. Jacks are time consuming to use, too, and they may not stay in place night after night.

The solution is to stock up on RV leveling blocks. The best RV leveling blocks are easy to use, stay securely in place, and can be made to fit no matter your situation. 

Top 7 Best Leveling Blocks for RV use - Comparison

What is an RV Leveling Block?

An RV leveling block is key to your family’s convenience and literal stability when you’re parked on hills or at an angle. It isn’t considered essential to your safety the way a chock block is, though you’ll probably put the leveling blocks out soon before the wheel chocks.

What are leveling blocks? They are large and typically stackable blocks you can use to level or support one side of the RV. You can set them up on the ground and then pull the RV forward until the wheels are on top of them. This raises the height of those particular wheels so that all of them are level.

In a modest case, it prevents your drawers and doors from slowly sliding open. In a severe case, the wheel leveling blocks prevent appliances from shifting and items from sliding off every flat surface in the RV. Wheel blocks are better than jacks, since jacks require more strength to use and may come loose. Wheel blocks are easier to remove and adjust, as well.

Here are Top 11 Best RV Leveling Blocks Full Review

We did a great review here for top rv leveling blocks. In these specific reviews, we tried to focus on which is bad and good there and explained deeply with the correct reason. Hope, our reviews will help you to choose the right leveling blocks for your RV, Trailer, Van, and campers. So lets start reading...

01) Tri-Lynx Model 00015 Lynx Levelers - 10 Pack

Editor Rating: 4.7 Out of 5

We’re recommending the 10 pack of Tri-Lynx levelers because they’re a better deal than the four pack, and in reality, you’re going to need more than 2 levelers in two locations to handle some serious situations. 

One reason we’re recommending this product is because of their modular design. They’re compatible with any camper or trailer.

Another benefit of their modular design is how they can be stacked like legos. You can connect them in a pyramid shape to create a stable, secure support.

You don’t have to worry about the leveling blocks falling over or shifting, potentially leaving you jarred awake as things shift suddenly.

The blocks are large enough and steady enough to act as a support for other equipment like jacks. And you can put them on top of other supports like wood boards and concrete blocks, though they can shift if the underlying support moves.

The blocks are relatively easy to handle; they weigh less than a pound each, and you can store them in a carry-bag sold with the leveling blocks.

They won’t rot or splinter like the wood boards many people try to use instead. The open pattern allows water to drain through them and away from the RV. They won’t create a massive mud-puddle you’ll have to deal with in the morning.

One downside of these blocks is their limited weight range. A number of people have driven the wheels of a heavy camper over an assembled set and had them shatter.

This isn’t an issue if you jack up a trailer, put the blocks underneath, then lower the jack. Don’t use them as wheel chocks; they aren’t designed for that. 

Pros
  • Modular
  • Versatile
  • Water won’t ruin them
Cons
  • Cracks into pieces if you drive over it 

02) Camco Brand Heavy Duty Leveling Blocks, Model 44505, 10 pack

Editor Rating: 4.6 Out of 5

Camco manufactured these strong leveling blocks to handle almost any load. These leveling blocks are heavy duty enough to support hydraulic jacks, tandem axels, tongue jacks and other heavy loads.

You can assemble them like legos into both vertical stacks and horizontal planes.

One downside is that they don’t stay together as well as lego, so don’t try to use them like chock blocks or expect an assembled load to handle a shifting burden.

These versatile loading blocks can be connected to support a tire or cover up a hole, and unlike the Tri-Lynx, you can drive over them. The plastic is UV resistant and water-proof. It is far better than using a board for the same purpose. It won’t rot, and it won’t harbor bugs.

However, the plastic can’t handle extreme cold. The plastic will do fine in the summer sun and barely freezing weather. If you have it outside in -20° weather, it will crack and even chip though it isn’t under load. If the material is breaking down like this, it will shatter under load.

They come with a basic plastic storage bag. The group of ten costs a little under seven pounds.

One downside with their design is that they don’t handle uneven pressure well. They’re designed to be laid down on flat pavement before a vehicle drives up and onto them or over them.

The problem is that when you put them on an uneven surface like gravel or rocky ground and do the same, they’ll break. Don’t try to put them over a pothole and then drive over them, either. 

Pros
  • Easy to assemble 
  • Can handle the heaviest RV loads
Cons
  • Can only be used on smooth pavement 
  • Can’t handle extremely cold temperatures 

03) 2-Pack Camper Leveler and Chock Kit, Andersen Model 3604 x2 

Editor Rating: 4.5 Out of 5

Whether you want to level your RV, hold it in place or do both at the same time, this Anderson leveler and chock kit is perfect for you. 

These RV leveling blocks are incredibly easy to use. You can have them securely in place in a matter of minutes. Yet you can precisely level your RV with them. You can adjust the level by increments of half an inch.

Note that these levelers can only lift up to a height of four inches. An advantage of this model is that you may only need to put the chock block/levelers on one axle per side to be done.

They’d be put on the low side of the trailer. For extra piece of mind, you can use extra chock blocks, and you should if on a steep hill or incline. 

One point in favor of this product is that it can support a wide range of tires. It can support tires up to 32” in diameter. In theory, they can support a load of up to 10,000 pounds.

The manufacturer says 30,000 pounds, but there are complaints of them breaking under half that weight. If the levelers are cracked for any reason, don’t use them because they may fall apart under load.

One downside of this model is that they may break if dropped. Don’t drive over them; that can break them. 

Pros
  • Fast to set-up and simplifies parking the RV all in one go 
  • Chock blocks and leveling blocks in one 
Cons
  • Maximum four inch height 
  • Can’t drive over them without breaking them 

04) Camco Brand Yellow Drive-On Tri-Leveler, Model 44573

Editor Rating: 4.5 Out of 5

This RV leveling block, the model 44573 by Camco, is one of the best RV leveling blocks for those who want to be able to drive up onto it;

it is literally designed for that, in contrast to several other RV leveling blocks on our list that would crack or shatter if you tried to do this. 

Simply drive up onto it; it can handle that stress. And better yet, these levelers could raise the RV by up to almost four inches. 

One point in its favor is that it can handle almost any size tire, since it is an open design. You can put the leveler in front of or behind the wheel and drive onto it.

The downside is that the product isn’t very wide; you have to locate it precisely to have it work properly. You should only use them on concrete or flat pavement, because they will otherwise sink into mud and gravel.

They tend to slide on wet pavement, too, when you try to drive up onto them. Don’t use these as wheel chocks. See our other listings to find RV levelers that can act as chock blocks. They have a load capacity of 3500 pounds. The “super” model of this product costs up to twice as much, but it is rated for up to three times the load.

For most people, these RV leveler blocks are good enough, as long as you’re driving a smaller trailer. That model would be better for a double axle trailer than the Model 44573 leveler.

The Model 44573 cannot be used for a double axle trailer at all, because there’s no space between the wheels to put them. 

Pros
  • Can drive up onto 
  • Bi-directional 
Cons
  • Can’t use on wet pavement or off pavement 
  • Can’t be used as wheel chocks 

05) Quality Plastics Brand Utility Block, Four Pack

Editor Rating: 4.4 Out of 5

This is the only model of utility blocks made by Quality Plastics. The product includes four interchangeable utility blocks. Each block is just over nine inches square, making it relatively easy to get under your RV or trailer tires.

These leveling blocks are all a uniform one and a half inches thick. They’re simple to add, subtract and adjust assuming you have the room.

You can nest them together to create a stable, higher support. Getting your tires onto that higher platform is not as easy as other products on this list.

A minor issue with these blocks is that they won’t necessarily stay nested if subjected to off-balance pressure. This means that they’ll stay in place if you’re lowering the side of a trailer onto the stack while you change a tire, but it may not stay in place if you have three holding up a wheel and the stack gets kicked or simply shifts.

If you overload them, the interlocking connections could break and then they’ll slide around at will. 

Conversely, the closed blocks won’t sink in the mud or capture water the way some of the other products on our list of the best RV leveling blocks would. The only exception is the round recessed spot in the middle, though this can’t hold much water. Being plastic, it won’t rot or attract bugs like the conventional wood boards used for this purpose.

The plastic itself won’t fade or degrade on exposure to sunlight for years. These blocks are big enough for small trailers, but they aren’t large enough for class A trailers. They’re about the size of leveling jack pads.

However, they can be used as leveling jack pads. Only load them with maybe two to three thousand pounds apiece, ideally less. 

Pros
  • Simple to install, adjust and remove 
  • Won’t sink in mud 
Cons
  • Can’t handle heavy loads or large trailers 

06) Camco Model FasTen 4x2 Leveling Blocks for Dual Tires

Editor Rating: 4.4 Out of 5

These RV leveling blocks are specifically designed to work with dual tires. The long but narrow blocks can support both of your tires at the same time, as long as you aren’t driving a class A dual trailer.

They’re better suited for class C motor homes and small dual wheel trailers like Mini-C trailers. They’re unsuitable for big buses, too.
This product is sold in packs of ten. You can stack them like lego blocks to get the stack to your desired height.

They’re relatively easy to use. The open mesh design allows water to drain through them. However, you should try to use them on pavement instead of bare ground, because uneven weight distribution can damage them.

Do not overload them, or they will crack or outright break. If they crack, they won’t fit together and thus can’t be stacked. And if they crack, they cannot support a full load anymore, either; they’ll deform and potentially damage your RV tires. They can only handle a few thousand pounds per tire. 

One downside of this model is that they don’t handle rear wheels as well as front wheels. Nor should they be used as chock blocks. 

Pros
  • Works with double tires when few products do 
  • Easy to use whether you have a single or double axle 
Cons
  • Can’t survive being overloaded 
  • May crack if rear loaded
  • Not for use as chock blocks 

07) OxGord Brand RV Camper Leveler Ramps, Pack of 2 

Editor Rating: 4.3 Out of 5

This multi-tiered leveler is a simple to use ramp. The long pull-up allows you to have plenty of room for your tires, and it distributes the weight over a broad area so they are less likely to crack when you pull a heavy vehicle up onto them.

You don’t have to figure out how to stack blocks or adjust the level; if you want to go higher, simply pull up a little further.

The multi-level design also allows you to use it as a support for any other equipment like jacks. 

One issue with these RV levelers is that they’re listed as being good for up to eight thousand pounds each, but they’re really only good for five thousand pounds each. 

Try to load them with six or seven thousand pounds, and there is a fair chance they’ll crack. Once that happens, it may totally collapse the next time you pull upon on it.

However, six thousand pounds is still pretty good given the weight range other RV levelers can handle. You can reduce the odds that the unit will crack if you use it on pavement. And they aren’t meant to be used with double axle trailers at all. 

Pros
  • Easy to use for any purpose 
  • Can handle being driven on
  • Go a little higher by pulling up instead of trying to adjust them 
Cons
  • Can’t support the high load listed on the product 
  • Can only be used on flat pavement 

08) BUNKERWALL Brand Model BW4203 Tandem Axle Leveler Ramps - 2 Ramps 

Editor Rating: 4.4 Out of 5

This product is sold as a pair, so you receive two axle leveler ramps. Better yet, they can support both single and double axel trailers. There’s no problem with trying to get an RV leveling block between two axels. 

The black and red color pattern makes it easier to determine when you’re close to the edge so you do not drive past it. That safety feature makes this one of the best RV leveling blocks for tandem axel trailers.

The ten inch width also makes it easier to pull up onto without worrying you’re an inch too far to the left or right. 

Forget easy stacking – this design simplifies the difficult task of getting the RV onto the ramp. It can lift wheels up to four inches off the ground. The plastic material won’t rot and is bug proof.  It can support, in theory, up to ten thousand pounds apiece.

The downside is that they really only handle about five thousand pounds each before they start to crack under the load. Another issue is that they slide easily on wet pavement or gravel, though you can reduce this by putting anti-slip tape on the bottom. 

Pros
  • Supports double axel trailers 
  • Easy to drive up on and use 
Cons
  • Not as strong as advertised 

09) Valterra Model A10-0918 Stacker, Pack of 10 

Editor Rating: 4.3 Out of 5

This is another RV leveler that can stack like lego blocks to whatever height you need them to be. They are sold as a set of ten. The built-in side handles make them easy to manipulate.

Each block is roughly 8” x 10”; they’re each one and a half inches thick. Make it as tall as you need it to be, whether leveling an RV or lifting a trailer up off the ground to protect the tires during the off-season. 

They come with a carrying case to store them in when not in use. The flat top allows you to use them as levelers, tongue wheel supports or jack supports. They can support, in theory, ten thousand pounds. 

In reality, half that weight can cause them to bend. If they bend under your trailer, they are at risk of breaking when exposed to another load that large. 

You can spread them out under a dual axel trailer or broader support, though it can’t go up very high in this case. You can make a “ramp” you could drive a lighter trailer up onto or create a stair step support for another application.

One annoying aspect of the open frame design is that they capture rocks and gravel in the frame. You may still stack after that, but this affects its ability to let water drain through and makes them heavier.

However, large rocks sticking in them may make it impossible to stack until you get the rocks out. 

Pros
  • Easy to stack 
  • Versatile 
Cons
  • Not as strong as advertised 
  • Captures rocks and pebbles that are a pain to get out

10) Trailer-Aid "Plus" Tandem Tire Changing Ramp, Model 23

Editor Rating: 4.6 Out of 5

This product is designed to aid you in changing a flat tire on a trailer. That is why it lifts tires up to five and a half inches off the ground, one inch higher than the regular Trailer-Aid RV leveler by Camco.

The design is unusual in that it is designed to securely hold the tire once you drive up on it. This prevents the mistake of driving over the edge of the ramp and landing on the ground.

You can use it to lift up one side of the trailer to make changing the other tire easier. The bright yellow plastic makes it hard to lose or forget these RV levelers. 

It is a heavy duty ramp; it can theoretically hold up to 15,000 pounds, and they’ve been reported to hold 7500 pounds repeatedly without issue. It is strong enough to support a horse trailer.

Note that they do not work with tandem axles with a leaf spring suspension, and they really don’t work with any tandem axels at all. That is a serious problem when it is advertised as suitable for tandem tires.

The six to seven inch width makes these RV levelers incompatible with ultra-wide tires. Nor does it lift up very large tires far enough to be changed.

In every other case, the small, lightweight design is good enough to support your tires with a minimum of effort. 

Pros
  • Holds tires securely 
  • Works well for small tires 
Cons
  • Not compatible with tandem trailers 
  • Can’t support very wide tires 

11) Andersen 2-Pack Camper Leveler 

Editor Rating: 4.4 Out of 5

This is a large, complex RV camper leveler kit. While they’re not the easiest system to use, they are the best RV levelers for handling large tires.

These levelers can handle tires up to 32” in diameter. And with a little adjustment, it could support 15” truck tires on an RV, too.

The flexible design allows you to adjust the height of the wheel to anything within half an inch and four inches. 

You aren’t limited by the height of 1.5” blocks or the two or three levels on a drive-up camper leveler. This camper leveler comes with two rubber mats. That helps the RV leveler stay in place instead of sliding around on the wet ground.

The only downside here is how small the non-slip pads are. You also get a carry bag. You need it, given how bulky the set is. These camper levelers can act like wheel chocks. Know that you need to use the non-slip pads under the chock blocks for the best outcome in this case.

In general, you only need one leveler per side. There aren’t complaints about these RV levelers cracking under normal use at the weight range they’re supposed to support.

In theory, they can support up to 30,000 pounds. In reality, they regularly support ten and twenty thousand pounds without any problem. Up near the 30,000 pound limit, they may fail. That is especially true if you have a large tire with a heavy point load above it. It will support a class C trailer.

Conversely, that design feature means you could drive up onto the larger arc and then slip the matching piece under the end, holding the wheel in place at the desired height. 

Pros
  • Supports nearly any RV and trailer wheel size 
  • Wide range of potential wheel heights 
  • Can act as a wheel chock
  • Can drive onto it in some cases 
Cons
  • Bulky 
  • The non-slip pads are barely big enough 

Conclusion

We’ve provided our list of the top eleven recommended RV leveling blocks. We did this because we don’t all drive the same type of trailer or in the same conditions. Regardless of what size your trailer or trailer wheels are, you’ll find a great RV leveling block on our list. 

John S.
 

Hello guys! I'm a 37-years-old author, traveler, writer, blogger, and a camper. I enjoy life as much as I can and love to visit beautiful places in my RV. That's why while traveling I have decided to dedicate some time to share my experiences with everyone that might be interested in traveling, camping, and RVs.

Click Here to Leave a Comment Below 0 comments